911 Motorsports feature image

911 Motorsports

Review rating Review rating Review rating Review rating Review rating 4.7 Fact checked

* We independently evaluate all recommended products and services. If you click on links we provide, we may receive compensation.

When purchasing a product, price is the consumer's primary concern. At present, 911 Motorsports has 43 products for sale. 911 Motorsports products range in price from $14.95 to $529.95, and the average price of all the products is about $157.9.

We found that most of the 911 Motorsports products are manufactured by 911 Motorsport. The manufacturer provides 911 Motorsports with a steady supply of products, and they have a good cooperative relationship with each other.

You can confidently purchase 911 Motorsports products from the seller 911 Motorsports. The brand holds an average rating of 4.7, testifying to its excellent reputation.

911 Motorsports Best Sellers

Last Updated: Jan 12, 2025

911 motorsports Circle Cutter Guide - 5 pc. Kit - .380"

Use the chart in the pictures to find your plasma cutter and drag shield diameter.
Quick and accurate circle cutting. The stencils are offset to cut the indicated size from the center of the plasma arc, this allows a little clearance for easy assembly.
5 pc. kit includes 10 hole sizes. 1/2", 5/8", 3/4", 1", 1 1/4", 1 1/2", 1 3/4", 2", 2 1/2", 3". The outside radius acts as bonus sizes, add 2" for 380/430 sizes add 2 1/4" for 580 size.
Made in USA. Laser cut and etched from 1/8" cold rolled steel.

4x4 - Floor Jack Extension - Drop in Style

**Verify your jack is correct before ordering** Check pictures to find your jack saddle style. Bolt on - Fine thread is most common, 24mm-1.5 thread. Bolt on - Coarse Thread is found on Torin & Duralast jacks. Cross pin style is used on most 1.5 ton jacks. Drop in style was used on older jacks made more than 10 years ago.
Converts your floor jack into a universal 1 1/2" pin. The saddle alone gives a 2" extension, it comes with 6" and 11" extensions that you can stack to get a total of 16" above your floor jack. There are multiple pin styles to work with different floor jacks. We came up with a 4x4 saddle with one side for round tubes and another for standard frames.
Made in USA - Extension tubes are swaged from 1 1/2" DOM tube. Saddle is 1/4" A572 steel and everything has a nice Zinc plated finish.
Recommended limits – 3 ton or full jack rating w/ 6” extension –75% of jack rating w/ 11” extension– 50% of jack rating w/both stacked at 16” ext.

911 motorsports 2'x4' - RC Car Jump Ramp 40°-60° - 24"x48" - with 1/10 Scale Deck

Frame Only Option - Get the "Frame Only" and go to your local lumber store to pickup a sheet of 1/8" tempered hardboard. Home Depot has them pre-cut to 2'x4' sizes for only $6.50 ea. and they are the same textured hardboard that's included with our other kits. Search Home Depot for 1/8 in. x 2 ft. x 4 ft. Tempered Hardboard.
1/10 and 1/5 Scale Options - Both of these come with the ramp deck, the 1/10 scale has one sheet and the 1/5 scale comes with two sheets for more impact resistance for high speed hits. It takes 30-40min. to assemble frame, drill deck through pilot holes in frame, screw down deck and assemble legs.
This 2'x4' (24"x48") ramp is the perfect size to transport to your favorite spot and be wide enought to easily hit from any driving angle. Setup only takes a couple minutes and it folds down to 5" tall. Can be linked together for a full 8 foot wide ramp which is great racing!
Made in USA! - Aluminum frame is easy to assemble, start feet hold ramp solid at any angle, leg feet keep it planted. Ramp deck is 1/8" textured tempered hardboard, 1/5 scale ramp has two layers for more impact resistance. Ramp deck has good weather resistance, painting it will help if you want to leave it out permanently in wet climates.
Adjustable legs - 40° is a good long kicker (20-40'), 50° angle high jump launches well over 10' high, 60° angle is great for low to med. speed back flips.
This is a new product we just listed on 11/26/24 - Made in USA! - We also have other ramp sizes and styles available. Check out our store or message us with any questions.

2'x2' - RC Car Jump Ramp 40°-60° - Up to 1/10 Scale - RTR Ready to Run

Available as a DIY "Kit" that requires the ramp deck to be drilled through pilot holes in frame and screwed to frame (takes 20-30 min.) Or get the "RTR" kit which has the ramp pre-assembled, the legs will still need to be bolted on
This 2'x2' (24"x24") ramp is great for cars up to 1/10 scale, get two and link them together for a 4 foot wide ramp that's easy to hit at any angle. For larger RC cars, search for our 1/5 scale ramp and check out our Store for more options.
Made in USA! - Aluminum frame is easy to assemble, start feet hold ramp solid at any angle, leg feet keep it planted. Ramp deck is 1/8" textured tempered hardboard, 1/5 scale ramp has two layers for more impact resistance. Ramp deck has good weather resistance, painting it will help if you want to leave it out permanently in wet climates.
Adjustable legs - 40° is a good long kicker (20-40'), 50° angle high jump launches well over 10' high, 60° angle is great for low to med. speed back flips.
This is a new product we just listed on 11/25/24 - Made in USA! - We also have other ramp sizes and styles available. Check out our store or message us with any questions.

Short Round Saddle - Floor Jack Extension - Drop in Style

**Verify your jack is correct before ordering** Check pictures to find your jack saddle style. Bolt on - Fine thread is most common, 24mm-1.5 thread. Bolt on - Coarse Thread is found on Torin & Duralast jacks. Cross pin style is used on most 1.5 ton jacks. Drop in style was used on older jacks made more than 10 years ago.
Converts your floor jack into a universal 1 1/2" pin. The saddle alone gives a 2" extension, it comes with a 6" extension, 3" round saddle and Prothane brand polyurethane jack pad. The pad holds on tight, but easy to remove for normal jack use.
Made in USA - For up to 3 ton floor jacks - Extension tubes are swaged from 1 1/2" DOM tube. Saddle is 1/4" A572 steel and everything has a nice Zinc plated finish.
Check out our other products for more options. We have different saddle and extension length options. Along with a Big Flat Plate and 4 Point Jack Adapter, which also work with this.

36"x24" Plasma Cutter - Water Table Conversion Kit - Edge Clamp

Weld our kit together, then bolt onto your 36"x24" service cart (NOT included). Seal it up, add water and then you will have the best plasma table roll-around available. Actual outside dimensions of finished table and cart are 35.75”L x 23.75”W x 35.5"H.
*NOT* included: Service Cart or Plasma Cutter - Requires Harbor Freight #62587 - 36"x 24" service cart, will potentially work with other brands - Includes: plasma table ends, 4" flat-bar sides, cutting slats, long reach clamp, wave break, (6) cord holders, drain plug & new hardware.
Clamp option - 5/8" post for fixture/weld tables. Edge clamp style for our table & standard fab. tables up to 9/16" thick. The clamp is perfect for holding our Plasma Stencils and straight edges.
Cutting slats are 1/8" x 1 1/2" flat bar. 6 gallons of water leaves 5 1/2" of air space to limit splash back. The included wave break also prevents splashing when rolling around.
Made in USA!

Tube Bending Jig - Racer Kit for building roll cage, custom tube bumpers & tube chassis fabrication

Custom Tube Fabrication Design System - no more guess work, no more waste!
The Racer kit comes with everything you need to build a full cage or chassis. From the main hoop, down to traingulation tubes.
Includes a pair of medium hinges & a pair of large hinges along with more extensions to set up full main hoops. Also includes cope-ends and miters which makes simple tube joint setup much quicker and easier; plus two Tube Masters for complex copes.
Kits come in 1.25", 1.5", and 1.75" diameters and work with tubing one size up or down (within 0.25") of the jig size. For example, if you have a 1.75" diameter Tube Jig it can be used with 1.5" tube or 2" tube with minor adjustments to account for cope position.
Made in the USA

911 motorsports 4 Point Jack Adapter for Axle, Transmission, Transfer case, Fuel Tank, Bumper - Floor Jack Base

Jack **NOT** included. Floor Jack option includes bolt-on Adapter Pin that replaces the 24mm fine thread saddle mount on most 2+ Ton floor jacks. Confirm your saddle mount style before ordering.
Offers the versatility to lift parts that are large, heavy, and awkward with your transmission or floor jack. Check out the "911 Motorsports Floor Jack Extension" that fits on the Adapter Pin and makes your jack even more versatile.
Minimum height is 6", Max height is 12" above jack base. Top bars adjust from 7-28” wide. Bottom bars adjust from 6-25” wide. Comes with wrench for adjusting threaded supports and tightening bars.
800 lbs. capacity at maximum extension
Made in USA

Big Flat Plate - Jack Adapter - No Adapter pin

The Big Flat Plate measures 8"x10" and is made from 1/8" thick steel with a 1 1/2" DOM gusseted receiver tube. It comes fully welded and has a nice zinc-plated finish. There are holes on the corners and support gussets underneath for strap hooks.
**Look at chart in pics to confirm your jack's mount style** The Big Flat Plate requires replacing the stock saddle with our 1 1/2" adapter pin. If adding this to a 911 Motorsports Floor Jack Extension select "Already have adapter pin".
This is a cheaper alternative to our 4-point Jack Adapter and gives a lower profile. It only adds 2" to your jack height when working underneath vehicles on the ground or on jack stands. Good for transmissions, fuel tanks, and even as a motorcycle lift.
Made in USA

Plasma Stencil - Square Cutter Guide - 5 pc. Kit - .430"

Use the chart in the pictures to find your plasma cutter and drag shield diameter.
The stencils are offset to cut the indicated size from the center of the plasma arc, this allows a little clearance for easy assembly.
1/4", 3/8", 1/2" sizes are under sized by .060" to make a tight fitting hole for carriage bolts to be held in place.
5 pc. kit includes 10 hole sizes: 1/4", 3/8", 1/2",5/8", 3/4", 1", 1 1/4", 1 1/2", 1 3/4", 2". The outside acts as bonus sizes, add 2" for 380/430 sizes add 21/4" for 580 size.
Made in USA. Laser cut and etched from 1/8" cold rolled steel.

911 motorsports 4 Point Jack Adapter for Axle, Transmission, Transfer case, Fuel Tank, Bumper - Floor & Transmission Jack Bases

Jack **NOT** included. Floor Jack option includes bolt-on Adapter Pin that replaces the 24mm fine thread saddle mount on most 2+ Ton floor jacks. Confirm your saddle mount style before ordering. Transmission Jack option includes adapter that requires two 3/8" holes drilled through jack plate.
Offers the versatility to lift parts that are large, heavy, and awkward with your transmission or floor jack. Check out the "911 Motorsports Floor Jack Extension" that fits on the Adapter Pin and makes your jack even more versatile.
Minimum height is 6", Max height is 12" above jack base. Top bars adjust from 7-28” wide. Bottom bars adjust from 6-25” wide. Comes with wrench for adjusting threaded supports and tightening bars.
800 lbs. capacity at maximum extension
Made in USA

Plasma Stencil - Tri Slot Cutter Guide - 3 pc. Kit - .430"

Use the chart in the pictures to find your plasma cutter and drag shield dimeter.
Stencils are offset to cut a tight fitting slot.
Laser etched sizes, centerline marks and end of slot
Includes 3 stencils for 9 sizes: slot lengths are 2, 4, or 6 bolt lengths.
Made in USA. Laser cut and etched from 1/8" cold rolled steel. We sell and ship these direct using USPS.

Tube Rotation Gauge - Magnetic Angle Finder/Transfer Mount

Angle finder cube *NOT* included, this is just the mount bracket. We do offer the combo as another product, look in our store to find the combo.
Works on 1" to 4" tubing. Magnets hold strongest in the middle sizes.
Allows you to measure and easily transfer rotation angles, which helps for tube bending layout and notching.
Made in USA -- Neodymium magnets pressed into formed 10ga. steel with a yellow zinc plating.

2'x2' - RC Car Jump Ramp 40°-60° - Up to 1/5 Scale - RTR Ready to Run

Available as a DIY "Kit" that requires the ramp deck to be drilled through pilot holes in frame and screwed to frame (takes 20-30 min.) Or get the "RTR" kit which has the ramp pre-assembled, the legs will still need to be bolted on.
This 2'x2' (24"x24") ramp is great for cars up to 1/5 scale, it includes two ramp deck layers for better impact resistance for high speed hits. Best if you get two ramps and link them together for a 4 foot wide ramp that's easy to hit at any angle. For smaller RC cars, search for our 1/10 scale ramp and check out our Store for more options.
Made in USA! - Aluminum frame is easy to assemble, start feet hold ramp solid at any angle, leg feet keep it planted. Ramp deck is 1/8" textured tempered hardboard, 1/5 scale ramp has two layers for more impact resistance. Ramp deck has good weather resistance, painting it will help if you want to leave it out permanently in wet climates.
Adjustable legs - 40° is a good long kicker (20-40'), 50° angle high jump launches well over 10' high, 60° angle is great for low to med. speed back flips.
This is a new product we just listed on 11/25/24 - Made in USA! - We also have other ramp sizes and styles available. Check out our store or message us with any questions.

Plasma Cutter Straight Edge & Stencil - Magnetic Holders - 2 pc.

Holds straight edge or Plasma Stencil where a clamp won't reach
Allows easy positioning and holds firm to prevent movement while cutting
Each Mag Holder has 6 lbs. of pull and 3 lbs. shear strength using neodymium magnets
For up to 1/8" thick straight edge
2 Mag holders included & Made in U.S.A.

Plasma Stencil - Circle PRO Upgrade - Cutter Guide 5 pc. Kit - .580"

Use the chart in the pictures to find your plasma cutter and drag shield diameter.
These fill in the gaps and add more sizes to the original Circle Plasma Stencils
The stencils are offset to cut the indicated size from the center of the plasma arc, this allows a little clearance for easy assembly.
5 pc. kit includes 10 hole sizes. 7/16", 9/16", 11/16", 7/8", 1 1/8", 13/8", 1 5/8", 1 7/8", 2 1/4", 2 3/4" The outside radius acts as bonus sizes, add 2" for 380/430 sizes add 21/4" for 580 size.
Made in USA. Laser cut and etched from 1/8" cold rolled steel. We sell and ship these direct using USPS.

Round - Plasma Cutter Water Table for 55 gal. Drum/ 17 gal. tub - No Clamp

Tub NOT included - Comes with long reach clamp, plasma table frame & cutting slats. This round plasma table will sit on top a 55 gallon drum or common wash tub and includes an adjustable clamp to hold our Plasma Stencils and cutting guides.
Clamp option - 5/8" post for fixture/weld tables. Edge clamp style for our table & standard fab. tables up to 9/16" thick. The clamp is perfect for holding our Plasma Stencils and straight edges.
Fits standard 55 gallon drums or Behrens 17 gal. wash tub -NOT included- which are in stock at most farm & hardware stores for around $35.
All of the sparks/slag and most of the smoke is captured with 6" air gap above the water. The usable cutting area is 22" or 24" with the 17 gal tub. Cutting slats are 1/8" x 1 1/2" flat bar. Requires welding, about 10 minutes.
Made in USA!

4'x4' - RC Car Jump Ramp 50°-70° - 48"x48" - Frame ONLY - DIY Kit

DIY kit, comes with **Frame ONLY** - Requires you to get your own ramp deck, use 1/8" tempered hardboard. One layer is good up to 1/10 scale, two layers is necessary for 1/5 scale. Home Depot has a full 4'x8' sheet for $13 and they will cut it to size for free. The Home Depot style is best because it is textured on one side which gives great traction on the ramp.
The 4'x4' foot ramp is what you want for high speed and big air bashing. This will launch a stock Xmaxx a solid 15' high and well over 40' gaps.
Adjustable legs - 50° is a big air long jump, 60° high jump with a little distance, and a 70° step up bordering on a full vert ramp!
Made in USA! - Aluminum frame is easy to assemble, then setup and change the angle, there are additional bottom front start feet to support ramp in the higher positions. It folds down to 12" tall and drops to 6" for storing when legs are removed.
This is a new product we just listed on 11/29/24 - Made in USA! - We also have other ramp sizes and styles available. Check out our store or message us with any questions.

Third Hand Tube Holder - for roll bar/cage - flexible tubing clamp

Holds tubes for welding while still allowing fine adjustment
Arms are bendable, but strong enough to hold position
Uses Strong Hand pliers that clamp up to 2" tube
Arms are Made in the USA

Plasma Torch Conversion Rings for Plasma Stencils - 2pc. - .500" to .580"

These rings slide over your plasma torch and bump it up to a common size for use with our plasma stencils
Includes two rings, since they are a consumable
.275" size fits AG60/SG55 torches -- .300" size fits PT31 torches -- .312" size fits Thermal Dynamics cutmaster 42 -- .500" size fits Hypertherm 30 Air, max 40/43 and 800/900 models. Miller Ice 50/55 and 125c torches

911 Motorsports FAQs

Yes, 911 Motorsports is a legitmate brand on Amazon. After conducting a comprehensive analysis of 343 customer reviews for 911 Motorsports products on Amazon, we have determined its average rating. With a strong performance and good quality, 911 Motorsports has received an average rating of 4.7 from numerous buyers, indicating that 911 Motorsports are trustworthy and live up to their claims. Therefore, it is safe to make purchases from 911 Motorsports on Amazon.

Amazon has strict policies and safety measures in place that ensure only legitimate sellers and products are allowed on their platform. It also provides a secure payment gateway and offers buyer protection, ensuring your transaction is safe. In the unlikely event that there's an issue with your purchase, Amazon's customer service and return policies are designed to protect your interests.

If you're interested in 911 Motorsports and want to find more 911 Motorsports products, you can follow the steps below:

  1. Go back to FindThisBest's homepage.
  2. Type 911 Motorsports in the search box and hit Enter to see the search results.
  3. Find and click the correct 911 Motorsports to go to the new page.
  4. Select the products you want in the 911 Motorsports buying guide, and take a glance at the prices and features of the products.
  5. View the products interest you on Amazon to read the customer reviews and check the ratings. Besides, you can hit the "brand" to find more 911 Motorsports products.

We analyze millions of 911 Motorsports products reviews and customer reviews to recommend the best picks for most consumers. We have a professional team with decades of experience to test the products, which can help ensure that we provide our readers with accurate advice and best recommendations.

There are usually 5 to 10 products in a brand buying guide. We found 43 911 Motorsports products for sale, 20 of which were analyzed in detail and recommended to customers.

  1. Go to the 911 Motorsports page.
  2. Select the product you want in the 911 Motorsports buying guide, and then view the product on Amazon. For example, if you are interested in the top 1 product 911 motorsports Circle Cutter Guide - 5 pc. Kit -..., you can view it on Amazon page.
  3. Place your order on Amazon.

Most of the 911 Motorsports products are produced by 911 Motorsport. The manufacturer provides 911 Motorsports with a steady supply of products, and they have a good cooperative relationship with each other.

Our mission is to provide you with the most up-to-date and objective information about the 911 Motorsports products, helping you make more informed buying decisions. We recommend best choices of the products from the 911 Motorsports brand, helping you make better shopping choices with less time and energy.