Skip to content
MakerFocus feature image

MakerFocus

4.4 Fact checked

* We independently evaluate all recommended products and services. If you click on links we provide, we may receive compensation.

When purchasing a product, price is the consumer's primary concern. At present, MakerFocus has 39 products for sale. MakerFocus products range in price from $8.99 to $45.99, and the average price of all the products is about $22.82.

You can confidently purchase MakerFocus products from the seller MakerFocus. The brand holds an average rating of 4.4, testifying to its excellent reputation.

Share

MakerFocus Best Sellers

Last Updated: Jan 9, 2026

MakerFocus 4pcs 3.7V 3000mAh Lithium Polymer Rechargeable Battery 1S LiPo Battery with Protection Board Insulated Rubber Tape and JST 1.25 Plug for ESP32 Development Board, Mesh Node T114

  • Charging Method: The recommended charging current is 0.6A, the maximum does not exceed 1.5A. The discharge current is recommended 0.6A, and the maximum does not exceed 1.5A
  • Overcharge Protection: When charging the battery, when the voltage reaches the highest battery voltage (4.2V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, forms overcharge protection
  • Over-discharge Protection: When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect

MakerFocus ESP32 LoRa V3 Development Board with 915 MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scenes

  • Support Arduino Development Environment: Support ESP32 + LoRaWAN protocol Arduino library, this is a standard LoRaWAN protocol that can communicate with any LoRa gateway running the LoRaWAN protocol
  • Easy to Use: With good RF circuit design and low-power design, ESP32 development board is the best option for smart cities, farms, homes, industrial control, house security, wireless meter reading and IoT developers
  • Highly Integrated: Integrated WiFi, LoRa, Bluetooth three network connections, onboard WiFi, Bluetooth dedicated 2.4GHz metal spring antenna, reserved IPEX (U.FL) interface for LoRa use. Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing

MakerFocus 4pcs 3.7V 1100mAh Lithium Polymer Battery 1S LiPo Rechargeable Battery with Protection Board, Insulated Rubber Tape and JST 1.25 Plug for ESP32 Development Board, Mesh Node T114

  • Overcharge Protection: When charging the battery, when the voltage reaches the highest battery voltage (4.2V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, form an overcharge protection
  • Over-discharge Protection: When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect
  • Short Circuit Protection: When an accidental short circuit occurs, the protection board will automatically shut down within a few milliseconds and will not be powered on again. Note that the cell is short-circuited (not through the protection board). The protection board will also fail due to continuous high current, or the components are heated and damaged

MakerFocus 1pcs 3.7V 10000mAh Lithium Polymer Rechargeable Battery 1S LiPo Battery with Protective Board, Insulation Coating and PH2.0 Plug for Raspberry Pi Battery Pack UPS and Other

  • Safety and Reliability: Our product utilizes a cutting-edge, A-grade lithium battery system. Compared to others, it offers superior energy capacity and density, along with more stable discharge performance and an extended lifespan. Additionally, it meets the stringent UN 38.3 safety standards, ensuring both safety and reliability
  • Charging Method: It is recommended to charge with a current of 2A, charging to 4.2V with constant current, converting to constant voltage charging when charging to 4.2V, and finally setting at 0.02C cut-off current of 200mA, at which time the battery is fully charged. Charging with currents and voltages higher than recommended may cause problems with the battery's charging, discharging, mechanical and safety performance, and may cause heat generation or fluid leakage
  • Discharging: The discharge current must not exceed 5A, and the battery must be discharged within the ambient temperature range of 0℃~60℃. High current discharge will cause a sharp decrease in the battery cell capacity and cause overheating

MakerFocus ESP32 LoRa V3 Development Board with 3000mAh Battery and 915MHz Antenna, Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scene

  • Support Arduino Development Environment: Support ESP32 + LoRaWAN protocol Arduino library, this is a standard LoRaWAN protocol that can communicate with any LoRa gateway running the LoRaWAN protocol
  • Easy to Use: With good RF circuit design and low-power design, WiFi LoRa V3 is the best option for smart cities, farms, homes, industrial control, house security, wireless meter reading and IoT developers
  • Highly Integrated: Integrated WiFi, LoRa, Bluetooth three network connections, onboard WiFi, Bluetooth dedicated 2.4GHz metal spring antenna, reserved IPEX (U.FL) interface for LoRa use. Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing

MakerFocus ESP32 LoRa V3 Development Board with 3000mAh Battery, Protective Case, 915MHz Antenna Integrated WiFi Bluetooth SX1262 CP2102 for Meshtastic IoT Arduino

  • Support Arduino Development Environment: Support ESP32 + LoRaWAN protocol Arduino library, this is a standard LoRaWAN protocol that can communicate with any LoRa gateway running the LoRaWAN protocol
  • Easy to Use: With good RF circuit design and low-power design, WiFi LoRa V3 is the best option for smart cities, farms, homes, industrial control, house security, wireless meter reading and IoT developers
  • Highly Integrated: Integrated WiFi, LoRa, Bluetooth three network connections, onboard WiFi, Bluetooth dedicated 2.4GHz metal spring antenna, reserved IPEX (U.FL) interface for LoRa use. Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing

MakerFocus 4pcs 3.7V Lithium Rechargeable Battery JST1.25 Connector 2pin, 952540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Compatible with ESP32 Development Board

  • Charging Method: The recommended charging current is 0.5A, the maximum is not more than 1A. The discharge current is recommended 0.5A, and the maximum is not more than 1A
  • Overcharge Protection: When charging the battery, when the voltage reaches the highest battery voltage (4.2V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, form an overcharge protection
  • Over-discharge Protection: When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect

MakerFocus TF-Luna LiDAR Range Finder Sensor Module, Single-Point Micro Ranging Module 0.2 to 8m Compatible with Pixhawk, Arduino and Raspberry Pi with UART / I2C Communication Interface

  • Working Principle: TF-Luna is a single-point ranging LiDAR, based on TOF principle. With unique optical and electrical design, it can achieve stable, accurate and highly sensitive range measurement
  • Product Characteristics: The product is built with algorithms adapted to various application environments and adopts multiple adjustable configurations and parameters so as to offer excellent distance measurement performances in complex application fields and scenarios
  • Extreme Cost Performance: Low-cost ranging LiDAR module, with 0.2-8m operating range. TF-Luna has a highly stable, accurate, sensitive range detection

MakerFocus 2pcs 3.7V 2000mAh Lithium Polymer Rechargeable Battery 1S LiPo Battery with Protection Board Insulated Rubber Tape and JST 1.25 Plug for ESP32 Development Board, Mesh Node T114

  • Charging Method: Recommended charging current of the battery is 0.4A, the maximum does not exceed 1A. The recommended discharge current is 0.4A, and the maximum does not exceed 1A. This battery protection board is equipped with two mos tubes, overcurrent protection (instantaneous) 3.2A-5A, charging voltage setting recommended 4.2V
  • Overcharge Protection: When charging the battery, when the voltage reaches the highest battery voltage (4.2V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, form an overcharge protection
  • Over-discharge Protection: When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect

MakerFocus 2 Set ESP32 LoRa V3 Development Board with 915 MHz Antenna and Case Integrated WiFi Bluetooth SX1262 CP2102 0.96-inch OLED Display Type C for Meshtastic IoT Arduino Intelligent Scenes

  • 2pcs WiFi LoRa 32: When use WiFi LoRa 32, you can use 2 pieces together. One is used for receiving and another one is used for sending
  • Support Arduino Development Environment: Support ESP32 + LoRaWAN protocol Arduino library, this is a standard LoRaWAN protocol that can communicate with any LoRa gateway running the LoRaWAN protocol
  • Easy to Use: With good RF circuit design and low-power design, ESP32 development board is the best option for smart cities, farms, homes, industrial control, house security, wireless meter reading and IoT developers

MakerFocus Raspberry Pi 4 Battery Pack UPS, V3Plus Expansion Board with 10000mAh Battery, Type-C Interface for RPI 5 4B 3B+ 3B 2B+

  • Two Power Supply Modes: outdoor portable type and indoor UPS power supply mode: 1) As an outdoor portable power supply, the main board is powered by a lithium battery. The maximum external power supply capacity is: 5.1V. 2.5A. 2) As an indoor UPS power supply mode: the UPS power supply interface is connected to an external 5V power supply, the power supply requires 5V 2A-3A, and the maximum output current can reach 5V 3A
  • 4+2LED Are Designed to Show the Status of Battery Power, Charge or Discharge: (1) 4 Battery power LEDs: Used to show the current battery voltage and power. (2)The function of the Power LED is to display whether the UPS is supplying power to the Pi, and the LED is on: it means the output is 5V. LED off: Indicates that there is no voltage at the output. 3) Charging indicator LED: When the UPS is externally charged via the TYPE-C USB interface, the Charge LED starts to work
  • The UPS Has Overcharge and Overcurrent Protection Functions: When the UPS externally outputs about 4A, the UPS will consider the external circuit to be in a short-circuit state and automatically cut off the output. The lithium battery board that comes with the UPS has an overcharge and overdischarge protection board. Prevents the battery from being overcharged and overdischarged when the external circuit is abnormal, thereby reducing the possibility of damage to the battery

MakerFocus 1pcs 3.7V 1000mAh Lithium Polymer Rechargeable Battery with Protection Board Insulated Rubber Tape and JST 1.25 Plug for ESP32 Development Board, Mesh Node T114, Electronic Devices

  • Charging Method: The recommended charging current is 0.5A, the maximum is not more than 1A. The discharge current is recommended 0.5A, and the maximum is not more than 1A
  • Overcharge Protection: When charging the battery, when the voltage reaches the highest battery voltage (4.2V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, form an overcharge protection
  • Over-discharge Protection: When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect

MakerFocus 2pcs 3.7V 1100mAh Lithium Polymer Battery 1S LiPo Rechargeable Battery with Protection Board, Insulated Rubber Tape and JST 1.25 Plug for ESP32 Development Board, Mesh Nodet T114

  • Overcharge Protection: When charging the battery, when the voltage reaches the highest battery voltage (4.2V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, form an overcharge protection
  • Over-discharge Protection: When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect
  • Short Circuit Protection: When an accidental short circuit occurs, the protection board will automatically shut down within a few milliseconds and will not be powered on again. Note that the cell is short-circuited (not through the protection board). The protection board will also fail due to continuous high current, or the components are heated and damaged

MakerFocus 4pcs 3D Printer Fan 12V, 40mm 12 Volt 0.08A DC Mini Quiet Cooling 40 x 40 x10mm with 28cm Cable for 3D Printer, DVR and Other Small Appliances Series Repair Replacement

  • Size: 40 mm x 40 mm x 10 mm; Working Voltage: DC 12V
  • Temperature of usage environment: -10℃ to +70℃
  • Bearing is high precision, long life and low noise

MakerFocus Wireless Tracker Supports GPS Galileo Multi-System Joint Positioning ESP32-S3 WiFi Bluetooth SX1262 UC6580 with 915MHz LoRa Antenna, 0.96-inch LCD Display for Meshtastic Arduino

  • Main Function: Based on ESP32-S3FN8, integrates UC6580 and SX1262 to provide fast GNSS solution for IoT, Wireless Tracker supports L1 + L5/L2 and GPS, GLONASS, BDS, Galileo, NAVIC, QZSS multi-system joint positioning, can track any object and upload the data by WiFi, Bluetooth, LoRa
  • Perfect Design: Low power design of dual frequency multi system based on 22nm technology. Onboard WiFi, Bluetooth dedicated 2.4GHz metal spring antenna, reserved IPEX (U.FL) interface for LoRa and GNSS use. Low power consumption, multi data transmission methods and interfaces to facilitate your development and application
  • Applications: Perfectly compatible with Arduino, GPS module can be widely used in development such as bicycle sharing services, tracking pets or livestock, locating vehicles, tracking children, etc

MakerFocus TFmini-s Micro LiDAR Module 0.1-12M LiDAR Range Finder Sensor Obstacle Avoidance Sensor Tiny Module Single Point UART I2C IO Compatible with Pixhawk Arduino and Raspberry Pi

  • Upgraded LiDAR Module: TFmini-s is an upgraded single-point micro ranging module based on TFmini. The dead zone is shortened to 10 cm, and the outdoor performance and accuracy of different reflectances are improved
  • Tiny Body Yet Big Wisdom: low-cost, small-size and low power consumption. Distance Resolution is 1cm, frame rate is 100Hz, ambient light immunity is 70Klux and central wavelength is 850nm
  • Tiny Yet Powerful: It is based on ToF (Time of Flight) principle and integrated with unique optical and electrical designs, so as to achieve stable, precise, high sensitivity and high-speed distance detection

MakerFocus GT-U7 GPS Module Satellite Navigation Positioning GPS Receiver Drone Microcontroller Compatible with NEO-6M 51 Microcontroller STM32 Arduino UNO R3

  • How to use the GPS module better, the link is obtained in the Product guides and documents, please download it before use
  • GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage
  • GPS baud needs to be set to 9600 instead of 4800; PPS pin is not needed unless using the GPS to drive a hardware high precision clock

Science Magnet Kits for Kids: Educational Magnet Science Projects Experiment Tools Physics Lab Kits Includes Bar/Ring/Horseshoe/Compass/Iron Powder

  • What is S.T.E.M.?: STEM stands for Science, Technology, Engineering, and Math, which constitutes many of the areas educators look to cover for science based activities. We are proud to say that his kit has a strong focus on STEM. A great physics STEM kit for student to enhance what is learnt from physics class
  • Experimental Activities: We provide some simple experimental ideas. In our picture, we can use it to open our minds to understand some assumptions about magnetism
  • Wide Applications: The magnet set provides basic accessories for magnetism, you only need some small tools in life to complete related experiments: such as pens, rulers, paper, and you can use your creativity to complete related experiments

MakerFocus ESP32 OLED WiFi Kit V3 Integrated WiFi Bluetooth CP2102 IoT Development Board with 0.96-inch OLED Display for Arduino Intelligent Scenes

  • Support Arduino Development Environment: WiFi kit 32 is a classic IoT Dev-board, it's a highly integrated development board based on ESP32 (Including WiFi and BLE), fully support Arduino development environment
  • Easy to Use: With good RF circuit and low-power design, ESP32 development board is the best choice for smart cities, farms, homes and IoT makers
  • Perfect Circuit Design: Onboard WiFi, Bluetooth 2.4GHz PCB antenna. Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing

MakerFocus 5pcs Voltage Meter, 2.5V-30V Mini Digital DC Voltmeter Two-Wire Voltage Tester with 0.28 inch LED Display

  • Detecting Voltage: DC 2.4V ~ 30V; Operating Voltage: 2.4V ~ 30V; Working Current:
  • High precision; Reverse connection protection; The decimal point is automatically shifted; Product certification: RoHS, CE
  • Able to Adjustable Voltage Resistance: Turn clockwise to lower voltage, it can work directly in 5V, 9V, 12V, 24V

MakerFocus FAQs