AURSINC Top 20 Products from Spectrum Analyzers Brand

AURSINC Tinysa Ultra+ ZS407 Spectrum Analyzer, 4.0 Inch 100kHz-7.3GHz Tinysa Handheld Frequency Analyzer, 2-in-1 RF Signal Generator 100kHz to 900MHz MF/HF/VHF UHF Input, HW V0.5.4 2025 Upgraded

Spectrum Analyzers

AURSINC 2025 Upgraded Tinysa Ultra plus ZS407 spectrum analyzer: With ultra-wide frequency range of 100kHz-7.3GHz, enabling you to capture and analyze a broader spectrum of signals precisely. With 4” IPS-TFT LCD (480×320) display can show a maximum of 450 points per scan, clearly presenting signal details and measurement results. Supports PC control, enabling easy data transfer and analysis

Ultra-Wide Frequency Range: The TinySA Ultra+ ZS407 Spectrum Analyzer covers a frequency range of 0.1 - 900MHz, with Ultra mode enabled up to 7.3 GHz, level calibrated up to 7.3GHz. Can observe signals up to 12GHz, which represents a significant improvement over previous models. It can accurately capture and analyze a broader range of signals, making it suitable for a variety of complex RF testing scenarios

Powerful Signal Generation Capability: The Tiny sa Ultra+ ZS407 can act as a Signal Generator with sine wave output between 0.1 MHz and 900 MHz, square wave output up to 6.3 GHz, or RF test signal output up to 7.3 GHz. It has a rich variety of signal generation types and a wide frequency range

Long-Lasting Battery: Equipped with a Li-polymer 3.7V 5000mAh battery, the battery life is significantly increased compared to previous models. It can meet the needs of continuous testing for a long time or outdoor operations, reducing the inconvenience of frequent charging and improving work efficiency. Built-in 32GB micro SD card, solving the on-site data storage issue, convenient for data sharing and storage

High-Gain Low-Noise Amplifier (LNA): The internal LNA gain can reach 20dB up to 7.3GHz, effectively enhancing the reception ability of weak signals. At the same time, at 100MHz, the DANL is as low as -169dBm/Hz when the LNA is on, reducing noise interference and improving the accuracy of signal measurement

Excellent Phase Noise Performance: The phase noise is -100dBc/Hz at a 10kHz offset and -103dBc/Hz at a 100kHz offset. The low phase noise indicates high signal purity, enabling more accurate analysis of signal frequency stability and spectral purity. It is crucial for high-precision RF measurement and communication system performance evaluation

Pakage List: 1x Tinysa ULTRA+ ZS407 Spectrum Analyzer (built-in 5000mah rechargeable battery); 1x 32GB Micro SD card (plugged in the host); 2x 30cm ALSR100 SMA cables; 1 x USB Type-C data cable; 1x SMA-SMA barrel connector; 1x TLanyard and touch plectrum; 1x Antenna with SMA connector; 1x stylus pen

Read more Read less

AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer, 4.0 Inch 100kHz-5.4GHz Handheld Frequency Analyzer with 32Gb Card, HW V0.4.6, 2-in-1 Signal Generator MF/HF/VHF UHF Input, 2025 Upgraded

Spectrum Analyzers

Buy on Amazon Find on eBay

[UPGRADED SPECTRUM ANALYZER] AURSINC Tinysa Ultra+ ZS406 installed with NEW HW V0.4.6, with 4.0 inch 480*320 touchscreen display, 100kHz to 5.4GHz widely measure range. Built-in 32GB micro SD card, solving the on-site data storage issue, convenient for data sharing and storage. Built-in 5000mAh battery, a fully-charged battery allows for at least 3 hours of operation, without frequent recharging interruptions

[WIDELY FREQUENCY RANGE] The Tiny sa ULTRA+ has an ultra measuring frequency range of 100kHz to 5.4GHz, spectrum analyzer for 100kHz-900MHz and Ultra mode up to 6GHz. Switchable resolution bandpass filters from 200Hz to 850kHz, you could fast and accurate execute measurement tests. Color display showing max 450 points providing gapless covering up to the full frequency range

[2 IN 1 DEVICE] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 100kHZ-900MHz, UHF square wave output between 800mHz-4.4GHz, Mixing signal output is between 4.4GHz-5.4GHz. Built-in calibration signal generator that is used for automatic self test and low input calibration

[200Hz-850kHz RBW] RBW frequency from 200hz to 850khz which can be set to match the measurement requirements, meet SBB two-tone test requirements and fast scanning. The RBW is as low as 200Hz, which can effectively distinguish adjacent signals and meet the requirements of SSB dual-satellite inter-modulation test. Input Step attenuator from 0dB to 31dB (can not be used not in combination with LNA)

[EXCELLENCE PHASE NOISE] Phase noise at 30MHz of -108dB/Hz at 100kHz offset and -115dB/Hz at 1MHz offset, DANL -166dBm/Hz. In the level menu, there is the LNA, which will provide 20db of extra gain if you have very low level signal (the LNA in tinySA ULTRA is only effective below 3.5GHz) The default maximum frequency is 800mhz, so you no longer have to switch between low and high range, and can monitor the complete range in one sweep

[PC CONTROL] This tinysa ultra can connect to a PC via USB, Tinysa-APP directly transfers data to the computer. The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel

[WHAT YOU GET] 1x Tinysa ULTRA Spectrum Analyzer (built-in 5000mah rechargeable battery); 1x 32GB Micro SD card (plugged in the host); 2x 30cm ALSR100 SMA cables; 1 x USB Type-C data cable; 1x SMA-SMA barrel connector; 1x TLanyard and touch plectrum; 1x Antenna with SMA connector; 1x stylus pen

Read more Read less

[Upgraded] AURSINC NanoVNA-H Vector Network Analyzer 10KHz -1.5GHz Latest HW V3.6 HF VHF UHF Antenna Analyzer, Measuring S Parameters, SWR, Phase, Delay, Smith Chart

Spectrum Analyzers

Buy on Amazon Find on eBay

[UPGRADED NanoVNA-H] New HW Version V3.6. It is upgradeable as new firmware is developed. With MicroSD card port now can have the measurement data or the screenshots saved in the it at anytime. Added battery circuit management, more secure. Redesigned PCB, you can connect to mobile phone with Type C-Type C cable (original PCB needs OTG cable), see a clear HD image on your phone. Added a ABS case, which is protective and dust-proof. Disply: 2.8 inch TFT (320 x240)

[IMPROVED FREQUENCY ALGORITHM] The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics

[MULTIPLE FUNCTIONS] The default firmware main function is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. The CH0 output level is increased to 0dBm when using the fundamental wave, resulting in more accurate reflection measurement

[SUPPORT ANDROID PHONE & PC SOFTSARE CONTROL] Designed a practical and simple control application on PC, you can download touchstone(SNP) files for radio design and simulation software. There is a PC interface that adds functionality and lets you work interactively on a bigger screen. Supports time domain analysis function (TDR). Compatible with most Android mobile phones, convenient for connecting to mobile phones. Support Windows Computer Control

[STRONG AND SECURE POWER SUPPLY] This VNA is battery powered or USB powered. Built in 650mAh battery, could work for 2 hours continuously. For longer measurement time, kindly connect an external power source. The product interface displays battery usage, providing a clear understanding of the power status

Read more Read less

AURSINC Upgrated NanoVNA-H4 Vector Network Analyzer, Lastest V4.4 9KHz-1.5GHz HF VHF UHF 4" Touch Screen VNA Antenna Analyzer Ham Radio, Measuring S Parameters, SWR, Phase, Delay, Smith Chart

Spectrum Analyzers

Buy on Amazon Find on eBay

LATEST VERSION V4.4: Developed by Hugen, the AURSINC NanoVNA-H4 comes with the latest V4.4 version—with a 9KHz-1.5GHz measurement range and enhanced dynamics during base wave operation. It features a 4.0-inch LCD touchscreen, and a compact, portable design. Its default firmware prioritizes antenna performance measurement, while the analyzer delivers excellent RF performance for S-parameter testing—perfect for ham radio operators, electrical engineers, and antenna builders needing efficient vector testing tools

IMPROVED FREQUENCY ALGORITHM: The improved frequency algorithm of Nano VNA H4 can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic. The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics. Used it to check out new cable or antenna installations and to routinely adjust the RF tuner for optimum

BUILT-IN MICRO-SD PORT & TDR FUNCTION: This antenna analyzer features a brand new panel and a new SD port for data storage, supporting up to 32GB memory cards (not included). Unlike older NanoVNA versions, it lets you customize the date and time for easier data recording. Added TDR functionality—widely used to quickly measure coaxial cable length and locate faults via impedance discontinuity calculations. The default firmware's main function is antenna performance measurement

PC CONNECTION & ANDROID CONTROL: Using the PC software NanoVNASaver, the Nano VNA H4 antenna analyzer can connect to your device, extract data for display on a computer, and save it to Touchstone files. You can also export Touchstone (snp) files via the software for use in various radio design and simulation tools. With its TX/RX method, the analyzer measures complete S11 and S21 parameters. To obtain S12 and S22 parameters, you only need to manually rewire the transceiver ports

WHAT'S INCLUDED: 1 x NanoVNA-H4 Host (built-in 1950mAh long-life battery), 1 x 4pcs SMA Male Calibration Kit (open/short/load + SMA female-to-female connector, for precise calibration), 2 x 6.3-inch (16cm) SMA Male-to-Male RG174 RF Cables, 1 x USB Type-C Data Cable, 1 x Type-C to Type-C Cable, 1 x Lanyard (with integrated stylus), 1 x Extra Stylus Pen, 1 x User Manual. It's a great antenna analyzer for your ham station—easy setup, no complex calibration

RELIABLE AFTER-SALES & TECH SUPPORT: We offer pro technical support for your AURSINC NanoVNA-H4 (usage & troubleshooting) to ease post-purchase worries. If you're unsatisfied with the antenna analyzer or run into any problems, don't hesitate to reach out. Our dedicated after-sales service experts will promptly respond. Shop confidently—we've got you covered from purchase to use

Read more Read less

AURSINC Allstar RF Node UHF SR-FRS Radio Programming Module Pi-hat for Allstar, Echolink, APRS, Digital Modes Compatible for Raspberry Pi 2/3/4, Pin to Pin Replace SA-818 Module, UHF Freq 400-470

Single Board Computers Raspberry Pi Starter Kits

Buy on Amazon Find on eBay

[Plug-and-Play Allstar Node] AURSINC Allstar Node SR-FRS Radio Programming Module (pin to pin replace SA-818 Module) is a versatile Raspberry-Pi hat that can be used for AllstarLink, Echolink, APRS, or any digital modes

[Working Mode] The both sides of the a TYPE C connecters have different function; PWR+COS(Flash) Communication with Raspberry on USB (main); PWR(GREEN) use /dev/ttyUSB0 to Change UHF RF node Frequency (only work when you want change UHF Freq (400-470)

[Additional Help] Use the program in this GitHub repository to program the radio module SR-FRS used for the Pi-Hat (github. com/jumbo5566/SRFRS) DCS Codes not support YET. Please refer to this link for setup questions: [allstarlink .github.io/adv-topics/sa818modules/#sa818]

[Compatibility issues] Compatible with Rpi 2/Zero 2/Zero 2W/3/3b/4/4b, it can communicate directly with the Rpi via the included Type C to USB cable. Please note that the USB connector should be properly inserted into the device

[Four section on This Program] Radio-Program the radio (frequency/tome/squelch); Volume -Set the volume level; Filters-Set filters; Version-Show the firmware version of the SA818

[SR110U Board OLED Indicators] PTT flash red led light means RF transmit; COS in blue means receiving the RF signal; COM in YELLOW means audio data transmit; PWR means power supply is normal

[Package list & NOTE] A SR-FRS Radio Programming Module, USB C Cable and an Antenna. NOTE: Before programming the SR-FRS module, make sure you HAVE consulted the band plan for your country and transmit on a frequency you are allowed to use

Read more Read less

AURSINC NanoVNA SAA-2N V2.2 Vector Network Analyzer, 50KHz-3GHz 4" Touchscreen HF VHF UHF VNA Antenna Analyzer Ham Radio with Storage Bag, Measuring S Parameters, Duplexer, VSWR, Phase, Delay

Spectrum Analyzers

Buy on Amazon Find on eBay

[Compliance] The NanoVNA SAA-2N developed by Hugen, designed in collaboration with OwOComm. Under the LGPL license agreement, it is completely manufactured according to the v2_2 files issued by OwOComm at Development Department, in line with the original technical specifications (Firmware update and manual: drive.google com/drive/folders/1Lr7AOTg2pAhYBZDfaiPVZTMZkFO14PMj)

[Upgraded NanoVNA SAA-2N V2.2 Version] Upgrade to the latest SAA-2N V2.2 vector network analyzer, featuring N-type connectors that outlast SMA ports for long-term reliability. It boasts a 4.0-inch touch screen for intuitive data viewing and testing, and is housed in a solid steel enclosure—solidly built and perfect for antenna testing with stable field performance. It comes with a carrying case that stores all accessories for easy portability

[Measurement Frequency Range] TheSAA-2N VNA antenna analyzer covers a frequency range of 50kHz to 3GHz. System dynamic range (calibrated): 70dB (up to 1.5GHz), 60dB (up to 3GHz); S11 noise floor (calibrated): -50dB (up to 1.5GHz), -40dB (up to 3GHz); Antenna analyzer performance: 1.005 (50kHz–1.5GHz), 1.02 (1.5GHz–3GHz). It supports up to 201 scanning points per selected frequency range, and the plots seem smooth without a lot of noise

[PC Connection & Bulit-in 3000mAh battery] The NanoVNA SAA-2N can be controlled by PC via VNA-QT software, supported for Linux, Windows (7+), Mac OS planned. It also support Nanovna-Saver for extracting the data for display on a computer, and for saving to Touchstore files. Built-in 3000mAh rechargeable battery for long-lasting field use (Micro USB interface)

[Calibration] The NanoVNA_V2.2 uses a similar user interface to the NanoVNA, but with a different technical architecture. The SAA-2N does not load the initial calibration data at startup, and does not automatically interpolate the calibration data after the user changes the frequency, must recalibrate or call back the calibration data after each startup and frequency change. Please read the user manual carefully before use to avoid damaging the device

[Packing List] 1* NanoVNA SAA-2N Host (Metal Shell, 3000mAh lithium-ion Battery); 1* Micro USB Data Cable; 2* 50cm N-type Male to Male RG142-PUR RF Cable; 1* N-type Male Calibration Kit-OPEN; 1 * N-type Male Calibration Kit-SHORT; 1* N-type Male Calibration Kit-LOAD; 1* N-type Female to Female Connector; 1* EVA Storage Bag for carrying out; 1*Touching Screen Paddle and Lanyard. It's great for amateur radio use, checking out antennas, coax feed lines, and many other applications

Read more Read less

Portable Tinysa Spectrum Analyzer, AURSINC V0.3.1 Handheld Frequency Analyzer, Signal Generator 100kHz to 960MHz MF/HF/VHF UHF Input ESD Protected Function with 2.8 inch Touchscreen

Spectrum Analyzers

Buy on Amazon Find on eBay

[Tiny Spectrum analyzer] AURSINC Tinysa spectrum analyzer produced by Hugen, with hardware V0.3.1. The firmware of the tinySA can be updated, for newest firmware version update, please refer to: tinysa .org. The version info displayed indicates "ESD Protection" with a diode to improve stability, sensitivity, anti-static level, and longevity

[Frequency Range] The tiny sa spectrum analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz. The tinysa includes all the components of a traditional heterodyne swept spectrum analyzer, with a color display showing 290 scan points covering up to the full low or high frequency range

[Built-in Calibration Signal Generator] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator enables automatic self-test and low input calibration

[PC Control] The USB interface realizes the Serial over USB (CDC) protocol and a large number of commands can be called through the serial interface. The commands can be used for measurements or updating internal settings. The Windows driver will automatically install upon connecting to a Windows PC. The driver for Linux is built into the kernel. Tinysa-APP is available to control the tinysa and capture its screen

[Package List] 1x Tiny Spectrum Analyzer(Bulit-in 500mah battary, 2.8inch touchsreen) ; 2x 20cm/7.87inch RF Cable; 1x USB-C Cable ; 2x SMA Female to Female Connector; 1x Touchscreen Pen; 1x SMA Telescopic Antenna

Read more Read less

AURSINC Upgraded NanoVNA-F V2 Vector Network Analyzer 50KHz-3GHz HF VHF UHF VNA Antenna Analyzer, 4.3inch Touchscreen, 5000mAh Battery, Measuring S-Parameters, SWR, Phase Delay, Smith Chart

Spectrum Analyzers

Buy on Amazon Find on eBay

[Upgraded Version] The NanoVNA-F V2 now supports the latest Firmware V0.6.0, enabling 301 sweep points for ultra-detailed frequency analysis. Allows for firmware upgrades through a virtual USB drive without the need for programmer, using the included USB Type-C cable to upgrade firmware

[Compact and Powerful] The nano vna f v2 features a 4.3-inch IPS LCD display (800*480) and a resistive touch screen, providing a wide viewing angle and minimizing eye strain during prolonged usage. It is equipped with an 5000mAh lithium battery for longer standby time, up to 7 hours of usage. It enables measurements of S-parameter, voltage standing wave ratio (SWR), phase map, group delay, Smith chart, DELAY, POLAR, LINEAR and more

[Improved Frequency Range] The measurement range of NanoVNA-F V2 is 50KHz-3GHz. TX/RX method can measure full S11 and S21 parameters, S21 dynamic ranges: 70 dB (1.5GHz), 60dB (3GHz); S11 dynamic ranges: 50 dB (1.5GHz), 40 dB (3GHz). The harmonic expansion of the output signal of the clock chip SI5351 is used to measure the frequency to 1000MHz. At 600M-1GHz, the dynamic range of S11 is 40dB (the standing wave ratio is less than 1.02)

[Design of Aluminum Cases] Rugged and durable aluminum alloy cases, shielding electromagnetic interference to ensure precise measurements. The SMA radio frequency interface enables seamless connectivity with various measurement devices. The device has a full touchscreen and three side buttons, making it easy and flexible to use

[PC Software Control Available] Using PC software NanoVNA Saver, it can connect to the NanoVNA, extracts data for display and save data in Touchstone files. The PC software enables us to export Touchstone (snp) files for various radio design and simulation software. For Win10 system, do not need to install the driver; for Win8 and earlier versions of the Windows system, need to install the driver: https://www. st.com/en/ development-tools/stsw-stm32102.html

[Packing List] 1x NanoVNA f v2 host, 1x SMA Open Calibration Kit, 1x SMA Short-circuit Calibration Kit, 1x SMA 50Ω Load Calibration Kit, 1x SMA-KK Double-Head Female Hole Adapter, 1x SMA-JJ Double-Head Male Pin Adapter, 1x SMA-JKW Elbow Outer Screw Inner Hole To Inner Screw Inner Needles Adapter, 2x 20cm SMA-JJ RG405 RF Cable, 1x USB Type-C Data Cable, 1x Stylus

Read more Read less

AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer with 50W Attenuator, 2025 Upgraded 100kHz-5.4GHz V0.4.6 Portable Frequency Analyzer with 32Gb Card, 2-in-1 Signal Generator 100kHz to 900MHz Input

Spectrum Analyzers

Buy on Amazon Find on eBay

[50dB Fixed Attenuator Spec] Rated to 50 Watts, DC to 3 GHz, N Female to N Male Directional. Attenuation: 50 dB ± 2.5 dB; Impedance: 50 Ω; VSWR and Attenuation Accuracy: 1.20:1 Max. Connector: N(M) Input, N(F) Output. Black Anodized Aluminum Heatsink Body

[Upgraded TinySA Ultra] Produced by Hugen, the AURSINC TinySA ULTRA+ ZS406 offers high-performance frequency coverage from 100kHz to 900MHz, and in ultra mode, the analyzer can reach up to 5.4GHz. It features a 4-inch touchscreen display and is installed with the latest hardware system V0.4.6. Built-in 32Gb micro SD card for data transfer and storage

[Frequency Range] The Tiny SA Ultra measures from 100KHz to 5.4GHz: Spectrum Analyzer for 0.1MHz-900MHz, with Ultra mode enabled, level calibrated up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters (200Hz–850kHz) enable fast and accurate measurement tests. The color display shows a max of 450 points, providing gapless coverage across the full frequency range

[2-in-1 Device] When not used as a spectrum analyzer, it can function as a signal generator: MF/HF/VHF sinusoidal output (100kHz–900MHz), UHF square wave output (800MHz–4.4GHz), and mixed signal output (4.4GHz–5.4GHz). It also includes a built-in calibration signal generator for automatic self-testing and low-input calibration

[PC Control] This TinySA Ultra can connect to a PC via USB, with the TinySA-APP directly transferring data to the computer. The USB interface implements the Serial over USB (CDC) protocol, and a large set of commands can be invoked via the serial interface. These commands can be used to perform measurements or update internal settings. The driver for Windows installs automatically when connected to a Windows PC, and the driver for Linux is built into the kernel

[200Hz–850kHz RBW] The RBW frequency (200Hz–850kHz) can be set to match measurement requirements, meeting SSB two-tone test requirements and enabling fast scanning. With an RBW as low as 200Hz, it can effectively distinguish adjacent signals and meet the requirements of SSB dual-satellite intermodulation tests. The input step attenuator ranges from 0dB to 31dB (cannot be used in combination with LNA)

[What You Get] 1x TinySA ULTRA+ ZS406 Spectrum Analyzer (4-inch touchscreen, 5000mAh rechargeable battery); 1x 50W Attenuator; 2x 30cm ALSR100 SMA cables; 1x USB Type-C data cable; 1x SMA-SMA barrel connector; 1x Lanyard and touch plectrum; 1x Antenna with SMA connector; 1x 32GB MicroSD card (pre-installed in the host); 1x Stylus Pen

Read more Read less

AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W, Supports C4FM YSF POCSAG NXDN DSTAR P25 DMR, Pi-Star/WPSD

Single Board Computers Raspberry Pi Starter Kits

Buy on Amazon Find on eBay

[Upgrade] AURSINC MMDVM radio station now equipped with raspberry pi zero 2w. Experience faster processing, smoother WiFi performance, and enhanced Stability

[EASY SET UP] Preload sofeware Pi-Star on TF card, no need to download again. Radio Frequency: (UHF:430-440) This is upgraded version, do not need to set RXOFFSET and TXOFFSET, they're default 0. Note: when you flash the TF card with new version software, please DO NOT copy on the TF card directly, use a write in tool to write the software on TF card

[EASY CHARGING] Free micro USB charging cable included, charged with power bank or connect to laptop or computer. The Hotspot will also work mobile in your vehicle if you tether it to your mobile phone network

[FIRMWARE V1.5.2] The MMDVM hotspot board supports updating to V1.6.1 (How to Update MMDVM_HS for WPSD 1.6.1: jumbo5566 .github.io). To speed up the operation, it is recommended to switch to an optimized system：https:// w0chp.radio/ wpsd/

[SUPPORT] C4FM YSF NXDN DSTAR P25 DMR and default work with UHF. Not compatible with Baofeng UV-5R, Baofeng RD-5R, 5X, 5R+, 5R Plus, etc UV series, BF series. Our test is in DMR mode, if you want to change the working mode, you need to configure it as needed Working mode parameters

[WIFI SSID] Need the 2.4GHz SSID as Pi Zero 2W doesn't support 5.8GHz. Ensure WiFi Password Type is WPA, not WEP. Power on hotspot for 2 minutes to auto-connect or follow instructions to connect the Hotspot to your router. After power on 2 minutes, go to pi-star /admin/ configure.php

[Note] Please refer to this website to test whether your device can receive or transmit signals: m7spi .co .uk/mmdvmcal/. If you encounter that the device cannot connect to network after setup, please kindly contact us. We will help resolve this issue

Read more Read less

AURSINC 4 Inch Hard EVA Protective Case for NanoVNA H4/TinySA Ultra - Waterproof Shockproof Storage Bag with Carry Strap, Foam Divider, Secure Fit for Vector Network Analyzer and Spectrum Analyzer

Spectrum Analyzers

Buy on Amazon Find on eBay

[Tailored Fit for 4-Inch Analyzers] Exclusively engineered for NanoVNA-H4 and TinySA ULTRA, with a contour-matched foam cradle that locks your device in place. A soft inner lining shields the screen and ports from scratches—no loose shifts during transport

[Heavy-Duty EVA All-Round Protection] Made of high-strength EVA material, the hardshell effectively fends off rain splashes, dust intrusion, and daily impacts.The smooth exterior is also easy to wipe clean

[Elastic Device Strap for Zero Movement] Elastic strap secures your device in place, preventing shifts during transport—critical for protecting the device's screen and ports from scratches during field testing or travel

[Properly Designed Mesh Pocket] Unlike top-loaded designs, our side-positioned mesh pocket keeps cables, calibration kits, and adapters firmly in place. No more spilling accessories when opening or closing the case—ideal for organized storage, while the durable zipper ensures quick access and secure closure

[Portable Design] Lightweight yet durable, equipped with a comfortable hand strap for easy carrying—ideal for on-site work and laboratory use, keeping your analyzer ready for use at all times

Read more Read less

AURSINC MMDVM Hotspot Board (V1.5.2) + Antenna Support UHF VHF Support P25 DMR YSF DSTAR NXDN POCSAG for Raspberry Pi-Zero W, 2W, Pi 3, 3B, 3B+, 4 (with OLED)

Single Board Computers Raspberry Pi Starter Kits

Buy on Amazon Find on eBay

[Frequency Range] MMDVM hotspot supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions)

[Multifunction] Hotspot board saves electricity, High quality TCXO, stable, low BER. Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG. Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules

[Applicability] AURSINC hotspot board supports Raspberry Pi 4, 3B, 3B +, Pi Zero W, Pi Zero 2W, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USBtoTTL or Bluetooth model). if you want a little processor power install on Pi 3 or Pi4, this is a great little hat for digital voice modes

When connecting the MMDVM board to a RPi 4, please note: If it works normally, no additional settings are required. If the SVC indicator does not flash, choose one of these methods (refer to the product diagram): 1. Remove the R1 resistor on the hotspot board. 2. Cut off the 2 RPi pin headers on the corners of the board

[Firmware Update] If the Raspberry fails to connect the hotspot board, please try update the firmware of the hotspot board by conducting the command: sudo pistar-mmdvmhshatflash hs_hat. More info pls view: amateurradionotes.com/pi-star-notes.htm#hotspotfwupdate. How to Update MMDVM_HS for WPSD 1.6.1: jumbo5566.github.io

[Importance] Please refer to this website to test whether your device can receive or transmit signals: m7spi.co .uk/mmdvmcal/. If you encounter that the device cannot connect to network after setup, please kindly contact us. We will help resolve this issue

How to Update MMDVM_HS for WPSD 1.6.1: Kindly refer to the following website: jumbo5566.github.io.

Read more Read less

AURSINC NanoVNA-H4 Vector Network Analyzer with 32GB Card, Latest V4.4 9KHz-1.5GHz 4" Touchscreen Nano VNA Antenna Analyzer Ham Radio, HF VHF UHF Measuring S Parameters, SWR, Phase, Delay, Smith Chart

Spectrum Analyzers

Buy on Amazon Find on eBay

[NEW ADDON] The built-in SD card slot and the 32GB micro card have solved the issue with saving on-site data; you can directly record data to the card, which is convenient for your data sharing and storage. Take the NanoVNA-H4 anywhere, anytime for on-the-go testing

[UPGRADED NANAOVNA H4 HW V4.4] Equipped with the latest HW 4.4 version, the NanoVNA H4 Vector Network Analyzer is a Hugen Original. It delivers reliable vector network measurement capabilities, features a compact handheld design, operates as a stand-alone device with a 4-inch LCD display, and is portable—supporting power supply via a 1950mAh battery or USB

[IMPROVED FREQUENCY ALGORITHM] The improved frequency algorithm of the NanoVNA-H4 utilizes the odd harmonic extension of the SI5351 to support a maximum measurement frequency of 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, the extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics

[ANTENNA PERFORMANCE MEASUREMENT] The default firmware's main function of the NanoVNA-H4 is designed for antenna performance measurement. Using the TX/RX method, you can measure the complete S11 and S21 parameters. If you need to obtain the S12 and S22 parameters, you will need to manually rewire the transceiver ports

[PC CONTROL] Using the PC software NanoVNASaver, the NanoVNA-H4 antenna analyzer can connect to a computer, extract data for on-screen display, and save it to Touchstone files. You can also export Touchstone (SNP) files through the software, which are compatible with various radio design and simulation software

[WHAT ARE INCLUDED] 1x NanoVNA-H4 host (with 1950mAh battery), 1x 32GB Micro SD card, 4pcs SMA male calibration kit (open/short/load/SMA female to female connector), 2x 16cm/6.3inch SMA male to male RG174 RF cable, 1x USB Type-C data cable, 1x Type-C to Type-C cable, 1x Lanyard with stylus, 1x stylus pen, 1x User Manual

Read more Read less

AURSINC SDR Radioberry HF SDR Transceiver Pi Hat for Raspberry Pi 4, Radio Card (RPi 4 Hat) Analog Devices AD9866 & 10CL025 12-bit Broadband Modem for Ham Radio SDR Transceiver

Single Board Computers Raspberry Pi Starter Kits

Buy on Amazon Find on eBay

Turn your Raspberry Pi to SDR Transceiver. Many amateurs have done a lot with Raspberry Pi ranging from cat control to converting it to a full fledged SDR transceiver. The latest kid in the block of SDR Transceivers is Radioberry. It's a combination of Raspberry Pi with a radio board developed using AD9866 12-bit microcontroller

Radioberry board actuall directly connects with the Raspberry Main Board. This braodband model mixed signal front end has been actually remodeled as a direct down and up conversion SDR Transceiver covering the entire HF spectrum (0-30 Mhz)

The radio card uses an Intell Cyclone 10LP FPGA, supporting the 10CL25 The firmware will be loaded via the raspberry pi. Power supply for the radio card is provided by the raspberry pi. The maximum receiving bandwidth is 384khz, supporting A and B dual receiving modes, and the output power is up to 10dbm

Now, a 025 mirror system is provided, which can run the SDR client directly with pihpsdr on the desktop, and the win/linux/mac client that supports SparkSDR supports the gateway working mode, and supports the expansion of the PA5Wv2 power amplifier to work in 3W mode, which can directly push the power amplifier above 100W

[Easy to set up] Connect Radioberry025 to Raspberry Pi 4/4B, then run the image file provided by Raspberry Pi 4B (Raspberry Pi 4B has a ready-to-use image, no settings required). Connect to the network cable and power supply of 5V and 2A, and you can start transmitting and receiving. It can be connected to a screen for use or not. Please refer to the picture for software configuration. Just fill in the IP of the Raspberry Pi and it can be used

[Packing List] Radioberry v2.0 x1, Heat dissipation fan x1. If you encounter any issues or have questions, please feel free to reach out to us at any time. We are here to assist you. (The new black radioberry version compatible with radioberry juice usb board and radioberry preamp board)

Read more Read less

AURSINC Radioberry Preamp Board V2, A Addition to Turn The Radioberry into a Small QRP Radio, HF Power Output 3W-5W for HF Amplification (10W-100W PA), for Raspberry pi 4,4b

Single Board Computers Raspberry Pi Starter Kits

Buy on Amazon Find on eBay

New Version V2: The output power of the amplifier board V2 is slightly higher than that of the previous version, with V2 reaching 3–5W. Technical Specs: Power in 6-8V (8.4V preferred); HF Power in: Tx from radioberry; HF Power out: 3-5W for for HF amplification. RF range: 1mhz-50mhz. Port Type: Input SMA, Output SMA. Supports SSB, FM, and AM

Designed for Radioberry SDR: This radioberry preamp board V2 is a nice addition to turn the radioberry into a small QRP radio. Seamless compatibility with Radioberry boards, making it a clean plug-and-play-style expansion, increased capability for your Radioberry

Amp board integrates with RPi 4: Pairs with Pi 4/4B for those building a Raspberry Pi-based QRP SDR radio, combining digital signal processing and radio functionality in a small form factor

What's Inside: 1x Radioberry Preamp Board; 3x SMA cable (1 for Rx ,1 for Tx,1 for ANT); 1x 8V Battery-powered Wire; 1x Connecting Row Needle; 4x Screw and Nut; 8x Plastic Column. Compact & Lightweight: Ideal for portable SDR radio setups, field use, or minimalist shack builds

How to Work: https:// jumbo5566 .github.io/pro/rb/2024/04/17/rb016_025 .html (Download the dedicated test image and run it directly for reception: http s://drive .google.com/file/d /1RzKAeha6EW8e4WeDlxpYBMPwdu-GsVZJ/view ?usp=drive_link)

Notes for prolonged continuous transmission: The bias voltage needs to be adjusted, and a range of 2.4–2.5V is safe. Additionally, adding a small fan for heat dissipation is recommended for better performance. For WSPR, there's a simpler method that can be achieved using an RP2040 + GPS. Please search for “RP2040 GPS” for details

Key Note: A Certain Level of Professional Knowledge Is Required for the Use of This Product

Read more Read less

AURSINC MMDVM Duplex Hotspot Module Dual Hat V1.5.2 with 0.96 OLED Display Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry Pi, Pi Zero (with OLED)

Single Board Computers Raspberry Pi Starter Kits

Buy on Amazon Find on eBay

[Extensive Compatibility] Supports DMR, P-25, D-Star and System Fusion. HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece. Compatible with the Raspberry Pi, including the Pi 1, 2/2b, 3/3b/3b+, 4/4b, Pi Zero, Pi Zero 2W

[Easy to Assemble] The firmware is pre-loaded and is easily upgraded via software. Onboard LEDs showing status (Tx, Rx, PTT, Mode). Pi-star control Mode selection: DUPLEX Mode/SIMPLE Mode

[Frequency Range] UHF 433-900MHz, VHF144-146MHz. (144-148, 219-225, 420-475 Main band, 842-950) It's best to work on the amateur band: 430-440 MHz. NOTE: TX=0, RX=0. To leave the screen on all the time In Pi-Star configuration, ensure you have "OLED Type 3" in the display type field at the top of the page, set Port to: modem

[Setting] Modify the modem type (any model ending in GPIO can be supported). Radio/Modem Type: STM32-DVM/MMDVM_HS-Raspberry pi Hat(GPIO). In the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to "1", this leaves the screen on all the time. Otherwise, it goes blank when idle

[Update New FW] (pi-star / expert / ssh access / user: pi-star pass: raspberry) You can directly run upgrade commands without the need to set jumpers (run in the Pi star terminal): sudo pistar-mmdvmhshatflash hs_dual_hat (if this command doesn't work, please try this command: mmdvm.club/index.php/wpsd .html)

Read more Read less

AURSINC Shari PiHat - Portable SA818 Ham Allstar Radio Interface Raspberry Pi Hosted Allstar Node, Compatible with Raspberry Pi 2/3/4/5, UHF Frequency Range 1W 420-450MHz/70cm Amateur Radio Operator

Single Board Computers Raspberry Pi Starter Kits

Buy on Amazon Find on eBay

[Upgraded SHARI PiHat] Add a 5V 1-1.5A USB-C port. Small, portable with self contained radio and antenna, SHARI(SA818 Ham Allstar Radio Interface) is designed for construction and uses in the amateur radio service, works with a Pi2/Pi3 or Pi4, SHARI RF output power is 500 to 1000 (default) milliwatts

[Allstar Node] SHARI PiHatU implements a Raspberry Pi hosted Allstar node using a NiceRF SA818 embedded UHF (420-450 MHz70cm) radio module; In order to create an Allstar node, SHARI plugs into two USB jacks on a Raspberry Pi2/Pi3 or Pi4 for power, the Allstar interface and radio programming (a short M/F USB extender cable can be used if desired)

[Power Supply] SA818 Ham Allstar Radio Interface is a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies

[Feature 1] Front panel LEDs indicate the status of SHARI-POWER (green), USB Audio CONNECTION STATUS (blinking green), COS (green) and PTT (red); SHARI PiHat uses 5 volts from the Pi, and the best place to measure it is from pin 8 (+5) to pin 9 (GND) of the SA818 module

[Feature 2] SHARI PiHat uses a single circuit board which contains installed surface mount (SMD) parts as well as 2 through-hole parts, a surface mount SMA connector and the SA818 (UHF) radio module; PiHatU also uses the Cmedia CM119B USB audio IC

Read more Read less

AURSINC Upgraded NanoVNA-F V3 Vector Network Analyzer 4.3" 1MHz–6GHz Antenna Analyzer Measuring S-Parameters Voltage Standing Wave Ratio SWR, Phase, Delay, Smith Chart Support RTC Real time

Network & Cable Testers

Buy on Amazon Find on eBay

[Upgraded Performance] nanovna f v3 with 4.3inch (800x480pixel) touchscreen display, 1MHz to 6GHz widely measuring range. With the optimally designed signal processing system, the scan speed is up to 200 points/s and the maximum scanning points is up to 801. The RF interface of antenna analyzer is SMA connector witch can be used to connect DUTs directly and the nanovna analyzer supports TDR function for cable lengths measurement

[Ultra Wide Frequency] Compared with the nanovna f v2 (50kHz-3GHz), the nanovna f v3 antenna analyzer measurement range is improved to 1MHz-6GHz. It can be used for S11 and S21 measurements. The S21 dynamic range of NanoVNA-F V3 is 65 dB, while the S11 dynamic range is 50 dB. The scan points is up to 101-801 and the calibration result storage is 12, covering up to the full low or high frequency range. The vna antenna analyzers are versatile and offer faster and more efficient operation

[Efficient and Worthwhile] The nano vna antenna analyzer is made of metal material, which is durable and can effectively shield electromagnetic interference. Powerful features, including automatic calibration, PC software control, compatible with NanoVNA-Saver to facilitate measurement data transfer, storage and export. Built-in 4500m-ah rechargeable battery, with C-type charging cable and LED charging indicator, suitable for indoor or outdoor application

[Multiple Measurement Functions] NanoVNA-F V3 antenna analyzer is suitable for antenna testing of MF/HF/VHF/UHF/SHF bands. It can also be used to measure filters, amplifiers, attenuators, cables, power dividers, couplers, duplexers and other RF components. Supports a variety of display formats: Log Mag, Linear Mag, Phase, Smith R+jX, Smith R+L/C, VSWR, Polar, Group delay, Resistance, Reactance, etc. Nano vna antenna analyzer are widely used, with fast response time and high operating efficiency

[Authentic & Package] NanoVNA-F V3 developed by Hugen. Package include AURSINC NanoVNA-F V3 host (with 4500mAh battery) display: 4.3 inch TFT x1, SMA OPEN/SHORT/LOAD calibration kit ×1, SMA-KK adapter ×1, SMA-JJ adapter ×1, SMA-JKW adapter ×1, 20cm SMA-JJ RG405 coaxial cable ×2, USB type-C cable ×1. The vna antenna analyzer provide reliable and accurate measurement results for ham radio operators and professionals.

Read more Read less

AURSINC MMDVM Hotspot Spot Radio WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W with Firmware V4.1.5 UHF VHF, Supports C4FM YSF NXDN DSTAR P25 DMR (with Ethernet Cable)

Modems

Buy on Amazon Find on eBay

[UPGRADE] AURSINC MMDVM radio station now equipped with Raspberry Pi Zero 2W. Experience faster processing, smoother WiFi performance, and enhanced Stability. This MMDVM radio is equipped with an Ethernet cable

[EASY SET UP] Preload sofeware Pi-Star on TF card, no need to download again. Radio Frequency: (UHF:430-440, VHF:144-146). This is upgraded version, do not need to set RXOFFSET and TXOFFSET, they're default 0. Note: When you flash the TF card with new version software, please DO NOT copy on the TF card directly, use a write in tool to write the software on TF card

[EASY CHARGING] Free micro USB charging cable included, charged with power bank or connect to laptop or computer. The Hotspot will also work mobile in your vehicle if you tether it to your mobile phone network

[FIRMWARE V1.5.2] The MMDVM hotspot board supports updating to V1.6.1 (How to Update MMDVM_HS for WPSD 1.6.1: jumbo5566 .github.io). To speed up the operation, it is recommended to switch to an optimized system：https:// w0chp.radio/ wpsd/

[SUPPORT] C4FM YSF NXDN DSTAR P25 DMR and default work with UHF. Not compatible with Baofeng UV-5R, Baofeng RD-5R, 5X, 5R+, 5R Plus, etc UV series, BF series. Our test is in DMR mode, if you want to change the working mode, you need to configure it as needed Working mode parameters

[WIFI SSID] Need the 2.4GHz SSID as Pi Zero 2W doesn't support 5.8GHz. Ensure WiFi Password Type is WPA, not WEP. Power on hotspot for 2 minutes to auto-connect or follow instructions to connect the Hotspot to your router. After power on 2 minutes, go to pi-star /admin/ configure.php

[Note] Please refer to this website to test whether your device can receive or transmit signals: m7spi .co .uk/mmdvmcal/. If you encounter that the device cannot connect to network after setup, please kindly contact us. We will help resolve this issue

Read more Read less

AURSINC Filter Attenuator, RF Demo Kit NanoVNA RF Tester Board for NanoVNA-H NanoVNA-F Vector Network Analyzer Kits

Network & Cable Testers

Buy on Amazon Find on eBay

[Evaluating and Learning Nanaovna] The RF Demo Kit is a NanoVNA RF test board independently designed by BH5HNU, with a size of 10*10cm / 3.94*3.94 inch. The demo calibration board for evaluating and learning nanaovna vector network analyzer, antenna analyzer test calibration learning, making sure your setup is working

[Tiny but Mighty] This RF Demo Kit is integrated with 18 functional modules. Can be used to measure 30MHz short wave low-pass-filter LPF, 100MHz FM high-pass filter HPF, 433MHz commonly used SAW band pass filter BPF, 6.5MHz ceramic trap BSFtt

[Note] The test parameters of the 18 patterns of the test board are described as follows. Two steps must be performed before testing: Step 1. Connect the two 20CM SMA to IPEX adapter cables to the NanoVNA-F machine. Step 2. Recalibrate the machine using the 13 Short, 14 Open, 15 Load, and 16 Thru circuits on the test board, and save the parameters to SAVE 0

[Applicability] It works with Nanovna-h / Nanovna-h4 / Nanovna-f / f v2 / f v3 / Nanovna saa-2n, and other nanovna antenna analyzer

[Package Included] 1x PCB RF tester board, 2 x 20cm U.FL connectors (Be aware the connectors on the test cables that connect to the PCB are only good for a hand-full of connection/disconnection cycles before they break)

Read more Read less

AURSINC

AURSINC Best Sellers

AURSINC Tinysa Ultra+ ZS407 Spectrum Analyzer, 4.0 Inch 100kHz-7.3GHz Tinysa Handheld Frequency Analyzer, 2-in-1 RF Signal Generator 100kHz to 900MHz MF/HF/VHF UHF Input, HW V0.5.4 2025 Upgraded

AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer, 4.0 Inch 100kHz-5.4GHz Handheld Frequency Analyzer with 32Gb Card, HW V0.4.6, 2-in-1 Signal Generator MF/HF/VHF UHF Input, 2025 Upgraded

[Upgraded] AURSINC NanoVNA-H Vector Network Analyzer 10KHz -1.5GHz Latest HW V3.6 HF VHF UHF Antenna Analyzer, Measuring S Parameters, SWR, Phase, Delay, Smith Chart

AURSINC Upgrated NanoVNA-H4 Vector Network Analyzer, Lastest V4.4 9KHz-1.5GHz HF VHF UHF 4" Touch Screen VNA Antenna Analyzer Ham Radio, Measuring S Parameters, SWR, Phase, Delay, Smith Chart

AURSINC Allstar RF Node UHF SR-FRS Radio Programming Module Pi-hat for Allstar, Echolink, APRS, Digital Modes Compatible for Raspberry Pi 2/3/4, Pin to Pin Replace SA-818 Module, UHF Freq 400-470

AURSINC NanoVNA SAA-2N V2.2 Vector Network Analyzer, 50KHz-3GHz 4" Touchscreen HF VHF UHF VNA Antenna Analyzer Ham Radio with Storage Bag, Measuring S Parameters, Duplexer, VSWR, Phase, Delay

Portable Tinysa Spectrum Analyzer, AURSINC V0.3.1 Handheld Frequency Analyzer, Signal Generator 100kHz to 960MHz MF/HF/VHF UHF Input ESD Protected Function with 2.8 inch Touchscreen

AURSINC Upgraded NanoVNA-F V2 Vector Network Analyzer 50KHz-3GHz HF VHF UHF VNA Antenna Analyzer, 4.3inch Touchscreen, 5000mAh Battery, Measuring S-Parameters, SWR, Phase Delay, Smith Chart

AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer with 50W Attenuator, 2025 Upgraded 100kHz-5.4GHz V0.4.6 Portable Frequency Analyzer with 32Gb Card, 2-in-1 Signal Generator 100kHz to 900MHz Input

AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W, Supports C4FM YSF POCSAG NXDN DSTAR P25 DMR, Pi-Star/WPSD

AURSINC 4 Inch Hard EVA Protective Case for NanoVNA H4/TinySA Ultra - Waterproof Shockproof Storage Bag with Carry Strap, Foam Divider, Secure Fit for Vector Network Analyzer and Spectrum Analyzer

AURSINC MMDVM Hotspot Board (V1.5.2) + Antenna Support UHF VHF Support P25 DMR YSF DSTAR NXDN POCSAG for Raspberry Pi-Zero W, 2W, Pi 3, 3B, 3B+, 4 (with OLED)

AURSINC NanoVNA-H4 Vector Network Analyzer with 32GB Card, Latest V4.4 9KHz-1.5GHz 4" Touchscreen Nano VNA Antenna Analyzer Ham Radio, HF VHF UHF Measuring S Parameters, SWR, Phase, Delay, Smith Chart

AURSINC SDR Radioberry HF SDR Transceiver Pi Hat for Raspberry Pi 4, Radio Card (RPi 4 Hat) Analog Devices AD9866 & 10CL025 12-bit Broadband Modem for Ham Radio SDR Transceiver

AURSINC Radioberry Preamp Board V2, A Addition to Turn The Radioberry into a Small QRP Radio, HF Power Output 3W-5W for HF Amplification (10W-100W PA), for Raspberry pi 4,4b

AURSINC MMDVM Duplex Hotspot Module Dual Hat V1.5.2 with 0.96 OLED Display Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry Pi, Pi Zero (with OLED)

AURSINC Shari PiHat - Portable SA818 Ham Allstar Radio Interface Raspberry Pi Hosted Allstar Node, Compatible with Raspberry Pi 2/3/4/5, UHF Frequency Range 1W 420-450MHz/70cm Amateur Radio Operator

AURSINC Upgraded NanoVNA-F V3 Vector Network Analyzer 4.3" 1MHz–6GHz Antenna Analyzer Measuring S-Parameters Voltage Standing Wave Ratio SWR, Phase, Delay, Smith Chart Support RTC Real time

AURSINC MMDVM Hotspot Spot Radio WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W with Firmware V4.1.5 UHF VHF, Supports C4FM YSF NXDN DSTAR P25 DMR (with Ethernet Cable)

AURSINC Filter Attenuator, RF Demo Kit NanoVNA RF Tester Board for NanoVNA-H NanoVNA-F Vector Network Analyzer Kits

AURSINC FAQs

AURSINC

AURSINC Best Sellers

AURSINC Tinysa Ultra+ ZS407 Spectrum Analyzer, 4.0 Inch 100kHz-7.3GHz Tinysa Handheld Frequency Analyzer, 2-in-1 RF Signal Generator 100kHz to 900MHz MF/HF/VHF UHF Input, HW V0.5.4 2025 Upgraded

AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer, 4.0 Inch 100kHz-5.4GHz Handheld Frequency Analyzer with 32Gb Card, HW V0.4.6, 2-in-1 Signal Generator MF/HF/VHF UHF Input, 2025 Upgraded

[Upgraded] AURSINC NanoVNA-H Vector Network Analyzer 10KHz -1.5GHz Latest HW V3.6 HF VHF UHF Antenna Analyzer, Measuring S Parameters, SWR, Phase, Delay, Smith Chart

AURSINC Upgrated NanoVNA-H4 Vector Network Analyzer, Lastest V4.4 9KHz-1.5GHz HF VHF UHF 4" Touch Screen VNA Antenna Analyzer Ham Radio, Measuring S Parameters, SWR, Phase, Delay, Smith Chart

AURSINC Allstar RF Node UHF SR-FRS Radio Programming Module Pi-hat for Allstar, Echolink, APRS, Digital Modes Compatible for Raspberry Pi 2/3/4, Pin to Pin Replace SA-818 Module, UHF Freq 400-470

AURSINC NanoVNA SAA-2N V2.2 Vector Network Analyzer, 50KHz-3GHz 4" Touchscreen HF VHF UHF VNA Antenna Analyzer Ham Radio with Storage Bag, Measuring S Parameters, Duplexer, VSWR, Phase, Delay

Portable Tinysa Spectrum Analyzer, AURSINC V0.3.1 Handheld Frequency Analyzer, Signal Generator 100kHz to 960MHz MF/HF/VHF UHF Input ESD Protected Function with 2.8 inch Touchscreen

AURSINC Upgraded NanoVNA-F V2 Vector Network Analyzer 50KHz-3GHz HF VHF UHF VNA Antenna Analyzer, 4.3inch Touchscreen, 5000mAh Battery, Measuring S-Parameters, SWR, Phase Delay, Smith Chart

AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer with 50W Attenuator, 2025 Upgraded 100kHz-5.4GHz V0.4.6 Portable Frequency Analyzer with 32Gb Card, 2-in-1 Signal Generator 100kHz to 900MHz Input

AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W, Supports C4FM YSF POCSAG NXDN DSTAR P25 DMR, Pi-Star/WPSD

AURSINC 4 Inch Hard EVA Protective Case for NanoVNA H4/TinySA Ultra - Waterproof Shockproof Storage Bag with Carry Strap, Foam Divider, Secure Fit for Vector Network Analyzer and Spectrum Analyzer

AURSINC MMDVM Hotspot Board (V1.5.2) + Antenna Support UHF VHF Support P25 DMR YSF DSTAR NXDN POCSAG for Raspberry Pi-Zero W, 2W, Pi 3, 3B, 3B+, 4 (with OLED)

AURSINC NanoVNA-H4 Vector Network Analyzer with 32GB Card, Latest V4.4 9KHz-1.5GHz 4" Touchscreen Nano VNA Antenna Analyzer Ham Radio, HF VHF UHF Measuring S Parameters, SWR, Phase, Delay, Smith Chart

AURSINC SDR Radioberry HF SDR Transceiver Pi Hat for Raspberry Pi 4, Radio Card (RPi 4 Hat) Analog Devices AD9866 & 10CL025 12-bit Broadband Modem for Ham Radio SDR Transceiver

AURSINC Radioberry Preamp Board V2, A Addition to Turn The Radioberry into a Small QRP Radio, HF Power Output 3W-5W for HF Amplification (10W-100W PA), for Raspberry pi 4,4b

AURSINC MMDVM Duplex Hotspot Module Dual Hat V1.5.2 with 0.96 OLED Display Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry Pi, Pi Zero (with OLED)

AURSINC Shari PiHat - Portable SA818 Ham Allstar Radio Interface Raspberry Pi Hosted Allstar Node, Compatible with Raspberry Pi 2/3/4/5, UHF Frequency Range 1W 420-450MHz/70cm Amateur Radio Operator

AURSINC Upgraded NanoVNA-F V3 Vector Network Analyzer 4.3" 1MHz–6GHz Antenna Analyzer Measuring S-Parameters Voltage Standing Wave Ratio SWR, Phase, Delay, Smith Chart Support RTC Real time

AURSINC MMDVM Hotspot Spot Radio WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W with Firmware V4.1.5 UHF VHF, Supports C4FM YSF NXDN DSTAR P25 DMR (with Ethernet Cable)

AURSINC Filter Attenuator, RF Demo Kit NanoVNA RF Tester Board for NanoVNA-H NanoVNA-F Vector Network Analyzer Kits

AURSINC FAQs

Similar Brands