Best Chainsaw Carburetors of 2025

"I needed this for my Poulan Wild Thing 2375 with the early Walbro WT-324. Despite some initial doubts about the fit, the throttle linkage matched perfectly. It came with new fuel lines, allowing for easy routing. Everything fit well without any customization. Just remember the fuel line routing from the old carb, as it can get tricky. Overall, a simple and effective replacement that made my saw run great!"

"After neglecting my chainsaw for a while, it started running rough. So, I decided to replace everything since it was inexpensive. I found two surprises: the primer bulb intake is now on the left side and doesn't interfere with the throttle. The chainsaw started after a few pulls and runs smoothly now. Definitely worth the $18, and I recommend getting a new chain too!"

"The repair kit I received had no screws for the primary bulb, which I needed. Despite that, it was a great price!"

"I found it easy to install. The carb came pre-tuned, which is a nice change from the many I’ve dealt with that weren’t. The price was reasonable, and the kit had everything I needed. I prefer to replace the lines and primer bulb even if they seem fine."

"After not using my saw for four years, I decided to replace the gas line, primer bulb, return line, and spark plug. I pumped the primer until gas flowed in the return line, and it fired on the second pull. With a little adjustment, it runs just like new."

"Replacing the carb was a fun experience. I can't rate it less just because it didn’t include the other set of gaskets. Everything ended up working just fine!"

“I found the product to be exactly as advertised with everything included, making me very pleased and happy with my purchase.”

“When I ordered this for my Poulan PP4218AVX, I was a bit worried about the linkage being too long, but I encountered no fit or clearance problems with the carb. After minor adjustments, it now runs perfectly!”

“This replacement carburetor worked flawlessly for my Poulin P3314 chainsaw. I didn't have to make any modifications, and it functioned right away.”

“I was ready to toss my chainsaw, which would start and then die immediately. After cleaning the carburetor, it ran well for a bit but the issue returned. Then I found this aftermarket carb and for just $10, I decided to give it a shot. I installed it and used the saw for 5 hours without any problems. Unlike the previous carburetor, this one doesn't need special tools for adjustments, which is a huge plus at high elevation.”

“I had a no-name Chinese chainsaw that wouldn’t rev up. Instead of rebuilding the old carb, I opted for this one since it was only a few dollars more. I’m pleased to say that it started up after just a couple of pulls and didn’t require any adjustments.”

“I purchased this carb based on the positive reviews, and even though I haven’t installed it yet, I’m impressed with the great price and fast shipping. I’ll update my review once I install it.”

"I found the installation to be straightforward and the replacement carburetor worked great after a few adjustments."

"My chainsaw wasn't starting, but after using this replacement, it runs like a champ. The price was very reasonable!"

"I received the product quickly, and it was a perfect fit for my chainsaw, even better than the original."

"I used this kit on my Craftsman chainsaw, and it is now operational. I had some trouble figuring out the fuel line connections, but it ended up working. Most of the value was in the carburetor, which unfortunately didn't perform as expected. The original carb mounts better, but I thought a new one might improve performance. The chainsaw wouldn't start, and my adjustments to the needle valves didn't help. The vendor suggested a possible blockage but didn't provide guidance on locating it. They did send a replacement carburetor, but by then, I had already reinstalled the original, which works well. Overall, this kit helped restore my chainsaw to service."

"I installed the new carburetor and reassembled the chainsaw, but it wouldn't start. The new carburetor seemed to be built incorrectly. The choke bracket was misaligned, making it impossible to get fuel to start. I'm quite disappointed."

"I received the complete carburetor quickly, and after installation, my chainsaw fired up after just three pulls! I was able to cut a few trees, and it works great. This saw had been sitting idle for seven years."

"I needed new fuel lines for my Husqvarna 235 E-series chainsaw and was skeptical about this kit priced under $20. However, after installation, it cranked up on the second pull and ran perfectly. The kit included everything I needed, and I highly recommend it!"

"I purchased this kit for my Husqvarna 240 14” chainsaw that was tough to start and running poorly. After replacing the parts myself and tuning the carburetor, it works well now. Watching online videos really helped me through the process."

"I got this kit for my 235 Husky. After a bit of tuning, it starts and runs great. I'm very satisfied with the results!"

"I installed this on my Homelite 3816 (UT10660A) chainsaw. It wasn't running properly before, but this new carb fixed the problem. I did have to tune it to a lower idle, which I expected. Overall, it's a nice replacement."

"I found this product to be overall good and easy to install. It worked well for me."

"I have a Homelite 42cc UT10580, and while the filters, fuel line, and primer bulb were easy to install, the carburetor just wouldn't cooperate. No matter how I adjusted it, it didn't work. I ended up going back to the old carb, and it finally ran after that. I'm unsure what went wrong."

"I received a used carburetor with dirt on it, and it was pouring gas out of the top into the cylinder. They also sent two used spark plugs that looked scraped."

"This kit is priced very low for what you get. It needed very little adjustment after assembly. Now, my 8-year-old saw is as good as new!"

"I replaced the carb on my RM4218 easily. The hardest part was retuning it after installation, but it works much better than cleaning the old one or buying a new saw."

"I was initially skeptical about Chinesium carburetors, but this one works well. I started with 2-1/2 turns out on each screw and adjusted from there. The rest of the kit seems solid, although the spark plug looks generic but is still functioning."

"This kit was a great buy for me. It included a primer bulb, carburetor, tubing, and more than I needed. I recommend checking out internet videos before using it since there are no instructions. It requires a bit of manual dexterity, but it's manageable for most DIYers."

"I installed the carburetor in about ten minutes and had my chainsaw running like new with a few minor adjustments. My Echo CS-310 started right up after a few pulls, and with a tachometer, I tuned the L and H screws perfectly for my elevation."